HX100 SE FPV Quad FUTABA SFHSS

12,870円(税込)

購入数

Ultralight, quiet and powerful! With the tiny design of a 100mm wheelbase and the BT2.0 300mAh 1S battery, this small body contains incredible energy! This little beast will bring you an unprecedented outdoor flight experience!



BULLET POINT
Uses the lightest F4 1S Brushless FC V2.1 motor, which weighs 2.69g
without a cable. This FC has the efficient STM32F411CEU6 processor
and tuned Betaflight MATEKF411RX (MK41R), which allow for
maximum weight savings
Equipped with BetaFPV’s exclusively designed BT2.0 connector, it can
support 9A continuous current and 15A burst while the PH2.0 connector
uses 4.5A continuous current
The highly efficient combination of the light 1102 13500KV motor and
durable 65mm 2- blade props deliver a drone with excellent flight
performance and achieves a great noise-reducing function.
Super light with a total weight of 28.09g, installed with the customized
HX100 SE carbon fiber frame. It is specially made of a matted material
giving the frame more texture and greater durability.
The drone comes with BT2.0 - PH2.0 adapter cable in default, which is convenient for customer who uses PH2.0. We also released the BT2.0 tester and charger, its charging current has been upgraded from 0.5A to
1A, which makes the charging speed 2 times faster.

SPECIFICATION
Item: HX100 SE FPV Quad
Weight: 28.09g (without battery)
FC&ESC: F4 1S Brushless FC V2.1
Motors: 1102 13500KV Motors
Props: Gemfan 65mm 2-blade props(1.5mm shaft hole)
Camera & VTX : M01 AIO Camera 5.8G VTX
Frame: HX100 SE Carbon Fiber Frame
Canopy: Canopy for HX100 SE
Receiver Option: Frsky XM / DSMX / Futaba S-FHSS
Battery: BT2.0 300mAh 1S Battery
Flight time: 4 mins in a smooth outdoor flight, 2:30 mins in full throttle outdoor flight
BT2.0 CONNECTOR
BETAFPV exclusive designed BT2.0 connector has broken through the bottle-neck of PH2.0 connector. BT2.0 connector has decreased internal resistance of connector effectively allowing more current to be transferred, which means it supports 9A continuous current (15A burst). This means stronger power and longer flight time on 1S brushless drones while PH2.0 just supports 4.5A. You can enjoy more flight time without disturb of low voltage warning due to reducing voltage sag. For more instruction, click here to reach.



See the graph below of comparing the BT2.0 connector and PH2.0 connector (solid pin version) in BETAFPV 1S 300mAh battery. The discharge current is 9A in this test. The BT2.0 has double the time (about 2 minutes) and a 0.2v improvement in voltage sag.


Much more choices of BT2.0 series accessories.
We know some of pilots might have a question about how to deal with the old PH2.0 1S battery. So we provide some accessories like BT2.0 connectors for those people who want to convert the PH2.0 connector to BT2.0 connector.

BT2.0 Connectors (10pcs)
BT2.0 1S Whoop Cable Pigtail
BT2.0-PH2.0 Adapter Cable
BT2.0 Battery Charger and Voltage Tester
BT2.0 300mAh 1S Battery
FLIGHT CONTROLLER
F4 1S Brushless FC V2.1 - The lightest 1S brushless FC in the current market. With slim and sleek design, 2.69g in weight and better performance on function for maximum weight savings, power, and responsiveness.
FC

CPU: STM32F411CEU6 ( 100MHZ )
Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
Size: 29mm x 29mm, fully compatible with the whoop frame in the current market.
Firmware version: Betaflight MATEKF411RX (MK41R)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Power Cable: 60mm, with BT2.0 connector, 1.25mm motor header pins
ESC

Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM


MOTOR
Customized 1102 13500KV motor - With an ultra-lightweight of 3.01g and
ball bearing technology, the friction is reduced between the bearing
surfaces thus increasing the duration of the motor and improving its
efficiency.

CAMERA & VTX
The M01 AIO camera is a super Mini 5.8GHz FPV Transmitter + 600TVL FPV Camera + RG178 Antenna. It has both a fast response and a clear image.

What's more, the M01 vtx board is super light and perfectly suited for the
HX100 SE canopy. The Quad comes with a 25° and 35° camera tilt
mounts, the 35° mount is suitable for high-speed flight, while the 25° mount
is for lower speed flight. SmartAudio is supported.

Output power: 25mW
TVL: 600TVL
FOV: H:120°/V:100°
Video System: NTSC
Horizontal Resolution: 640X480 1/4”
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
Note: To change the frequency or output power via remote control, please check the manual Smart Audio. Download the STL file for the customized HX100 SE canopy.



PACKAGE
1 * HX100 SE FPV Quad
1 * BT2.0 300mAh 1S Battery
1 * BT2.0-PH2.0 Adapter Cable